Missionary Cradle
By Lazarus
This simple tie, also known as the Sex Sling, can be created using nothing but Foundations 1 techniques. It holds your partner in a “missionary” position. There are a few important risks to understand, however, that can make this tie much safer and more comfortable.
This has a similar effect as the Malasana Tie. The difference is that the Malsana runs the band behind your partner’s back instead of over the shoulder allowing you to bind your partner into a more extreme spread.
Risk Management and Safety
If tied tightly, this can hold your partner’s spine in a curved shape. Make sure that is a sustainable position for them.
In the form shown (with the tail going over each shoulder only once), there are only two strands pressing into your partner’s trapezius muscles. This bring two risks:
- The pressure on the muscles can be quite intense because it is concentrated on just those two strands. If you find this to be an issue, you can use a longer rope and go back and forth once or twice to make the straps wider.
- If you are moving around a lot, it can easily cause abrasions (rope burn).It can be helpful to allow your partner some protection for their shoulders, a shirt or maybe a towel. This can also help with the pressure issue.
If your partner has a great deal of hip mobility and their legs can move further apart than average, the shoulder straps can slide off the shoulders! If this happens, consider using the Malasana instead. Or you can use the left over tail to connect the cuffs together loosely in front as well to keep them together.
Rope Needed
- I used two 15’ (~4.5m) for this tie and had some left over, so that would be enough for someone a bit bigger than this model
- HOT TIP! If you use a longer rope, you can make the shoulder straps wider and more comfortable!
Prerequisites
More Like This…
Video
Missionary Cradle
Two short ropes and a few simple techniques are all you need to keep your partner in position and create some very helpful handles!
Step-by-Step
Start with a Single Column around the leg, just above the knee. I am going to use the Somerville Bowline. Somerville Bowlines are somewhat directional. You want to tie them so that the tail will naturally be flowing in the direction you want when the tie is complete. I want the tail to move toward my partner’s shoulders, so I start with it on that side. Wrapping the bight end around my partner’s leg like this.
Here the Somerville Bowline is done…
…and you can see the tail flows nicely toward the shoulder without tipping the knot over
It is okay to tie these a little looser than you might normally. That gives the cuffs the ability to shift slightly if you are moving a lot.
Repeat on the other side. Note that the node of both cuffs is facing the shoulder.
Bring the tail from one leg over the shoulder on that same side…
…and across the back to the opposite arm pit.
Don’t go across the back of the neck; you don’t want to run the risk of impacting the alignment of the vertebrae in your cervical spine.
Go under the opposite arm. Put your fingers under the other band. Feed the tail to those fingers…
…doing so outside the node of the Somerville Bowline. Pull it under the band. Reverse tension and pull it to the tightness level you want. Some like this quite tight, some do not. Experiment and discover what your partner likes!
(Here is where you would go back and forth a few times if you were using a longer rope.)
If you are using a shorter rope like I am and don’t have much left, lock it off any way you wish. Good options include Two Half Hitches, RTTHH, whatever.
If you have a bit of rope to use up, but not enough to go back to the other band, you could start with a Crossing Hitch, then bring the tail back the way it came, then wrap it around itself to use up the rest of the rope, locking off the last wrap by tucking it under itself.
Now do the same on the other side: Bring the tail from the other leg over the shoulder on that same side…
…and across the back to the opposite arm pit.
You can simply lay this one on top of the other, or you can connect them in several ways. But choose something relatively flat; you don’t want a bulky knot directly on the spine! I will show you a few options at the end.
Go under the opposite arm. Place your fingers under the under the band of the other Somerville Bowline, outside the node.
Run the tail under the band. Reverse tension.
Lock off however you wish. I did the same thing on this side as I did on the other.
Alternatives for the crossing point: A Crossing Hitch…
… doing the first tail pull on the lower side …
… then completing the Crossing Hitch.
Or a simple decorative weave.
One other point. If your partner has extreme hip mobility, it is possible for the shoulder strap…
…to slip off the shoulder. One solution for this is to make the cradle tighter, bending them into a tighter ball. Another is to use the Malasana Tie instead, which runs the band behind their back instead of over the shoulder and can hold your partner in an extreme spread.


